Engine Management

THINWALL AUTOMOTIVE 0.5mm 12V AUTO CABLE 11A ENGINE CAR LOOM WIRE VERY HIGH Quality 0.5mm Thinwall cable Perfect for Car Engine Looms Thinner than most @1.6mm Harsh Environment Automotive PLATED...

0-150psi high accuracy sensor with connector.1/8 NPT0.5v = 0PSI4.5 = 150PSI Pin A = GroundPin B = +5 VoltsPin C = Signal Out N.B. Insert wires through plug before crimping...

Race Engine Loom Rubber Grommet60mm Bulkhead hole | 16mm outlet | 78mm overallWill Fit All Ford Cosworth Cars.Very flexible great for race and kit cars.VERY HIGH QUALITY USED IN RACE...

Can bus keypad easily integrated with our PMU-16 and Ecumaster standalone EMU Black.  Very rugged and fully waterproof. 8 available colours which appear in the back light part of the unit, this can be used to...

CAN Lambda Link’s CAN-Lambda is an easy to use CAN-module that provides digital wideband sensor control via CAN bus and is compatible with leading aftermarket ECUs. The CAN-Lambda’s ability to...

LINK Ecu G4 G4+ G4X 4 bar MAP Sensor & Connector / Plug 4 Bar MAP Sensor  MAP Sensor capable of reading up to 4 Bar (3 Bar of boost)...

Bosch EV6 / EV14 - Fuel Injector Connector / Plug ConnectorVERY HIGH QUALITY USED IN RACE LOOMS AVAILABLE in SETS of 1 ,2 ,4,6 and 8 !The injector in the...

The EMU Black  stand-alone engine management system is designed to operate the most advanced and complex engines available. It is a successor of our proven system, EMU. Throughout EMU’s lifetime...

At BHP we have spent a long time perfecting the installation of Link ECU's into Cosworth YB Powered Cars including the Sierra & Escort RS Cosworth and a multitude of...

*Can to USB Box Required for Configuring.  Decades ago, the critical electronic components in a race car were the ignition coil and points. Race cars now feature advanced engine management...

LINK Plugin Ecu - XS Expansion Loom for Additional Inputs and Outputs   Xsl Expansion loom suitable for any Link Plugin Ecus where additional inputs or outputs are needed.

Terminating Resistor for CAN Bus Networks

Link G4+ G4X Air Temp Sensor (IAT1-8) 1/8" NPT complete with plug and terminals

Soldering Required for Assembly !

Cosworth YB Engine Loom Plug Kit Complete Plug Kit to re terminate the aging loom, this kit literally solves 99% of loom problems. Contains the following: 9 x 2 Pin...

Bosch LSU 4.9 Digital Wideband Lambda Sensor for Link ECU's Comes with Connector and Terminals Lead Length 40cm.

The Aim MXS Strada Car Dash Display is the evolution of MXL Strada, one of the most widely-spread dashes on tracks and streets all over the world. The MXS Strada...

Link G4+ G4X (CANPCB) Supplies USB output on PlugIns ECUs   This cable is require to add CAN / SERIAL Communications

Bosch Knock Sensor With Mating Connector ideal for Link ECU Motec Syvec etc

Bosch LSU 4.9 Digital Wideband Lambda Sensor for Link ECU's Comes with Connector and Terminals Lead Length 90cm.

*Requires a Can to Usb Box for Configuring ADU5 IP65 - Dust and Water Resistant ADU7 AutoSport Advanced Display Unit with Logging: The ADU7 AutoSport Display is identical in specification...

A CAN switch board is a tiny device to allow easy transfer of up to 8 switch states and 8 analog signals over the CAN bus. In addition to this, the...

ECUMASTER EGT to CAN The EGT to CAN module collects input signals from 8 EGT probes (K-Type thermocouples), converts the probe voltage into a numerical temperature figure and sends the...

Link Plug-In ECU & WIREIN ECU CAN cable and terminating resistor, 2m long ideal for Dash installs